Technical Specifications - "Touch pad" & "Sensor" Taps and Showers

“Touch Pad” Taps and Showers as per the “Pan” touch Plates with only one sensitivity area.

“Sensor” (hands free) Glass Finished plates for Taps & Showers.

Chrome finished “Sensor” (hands free) Taps.

Available in cold only or pre-set temperature depending on site requirements

POWER SUPPLY:
The power supply converts mains voltage to 24 volt AC, 750mA - 1A output to drive the Controller.

Specification:
Double insulated AC plug pack.
Input 240v AC 50 Hz.
Output 24v AC 750mA - 1A.
Cord length - Approx. 1.8m.
Plugs supplied 2.5m DC type.
Energy authority approval No. W/2354.

SOLENOID VALVES:
(NO WATER HAMMER) standard specifications: (6213 FROM BURKERT) WaterMark
Specification:
Voltage; 24v AC 1A
Polyamide coil
Valve body brass
Water Hammer free
Dimensions “typ” 10mm (3/8 half inch) 9cm (h) x 5cm (w) x 6cm (d)
Minimum cycles expectancy 300,000 – 500,000

WaterMark LICENCE NUMBER 60042                    WaterMark level 1           

Certification Date      11 February 2009                 Expiry Date         10 February 2014

AGA Certification Ref No 7444

CONT: TECHNICAL SPECIFICATIONS: TAPS & SHOWERS.

FLOW CONTROL:
Inline Flow Regulator – 6 litres per min for taps – 12 litres per min for showers – see PDF attachement for WaterMark and WELS ratings on our website.

SYSTEM CONTROLLER – TOUCH PADS:
(Complies to AS 3112)
This receives the pulse to initiate the water cycles. User activation by means of a touch sensitive stainless steel pad triggering device – sending output to initiate the opening of the Solenoid Valve.

• Proprietory “touch” sensor system

• Input 24V AC (from mains through an adapter)

• Size 12cm x 7.5cm x 2.5cm
  

SYSTEM CONTROLLER – HANDS FREE:
(Complies to AS 3112)
This receives the pulse to initiate the water cycles. User activation by means of swiping in front of the glass plate triggering device – sending output to initiate the opening of the Solenoid Valve.

• Proprietory “movement” sensor system (approx 4cm from front of glass)
• Input 24V AC (from mains through an adapter)
• Size 12cm x 7.5cm x 2.5cm

The FlushSaver infrared Sensor Tap is a wall-mounted Glass finished unit. Swipe for water activated pulse free operation, adjustable IR beam, quiet water hammer free operation. 10 second operation with externally adjustable timers (within 10% pre-set max and mins) and can be factory customised to suit customer requirements.

CRITICAL SPECIFICATIONS:

TOUCH PAD TAPS & SHOWERS:

FlushSaver Touch Pad Tap (stainless) – Model:                        FS-TP-TU-SS
FlushSaver Touch Pad Shower (stainless) – Model:                FS-TU-SH-SS
FlushSaver Touch Pad Tap (Glass) – Model:                              FS-HS-TU-GXX
FlushSaver Touch Pad Shower (Glass) – Model:                       FS-HS-SH-GXX

The FlushSaver Touch Pad Tap and Shower units are IC based with single timer circuitry for water deliverydelivery featuring “Two millimetre thick vandalism resistant stainless steel touch plate” activation. Features Nickel, Plated 3/8 inch, 1000kpa water hammer free Solenoid Valve. 5, 7.5 and 10 second operation for taps and 1 to 6 min operation for Showers (in 1 min increments within 10% pre-set max and mins) with lockouts that are set at installation. “FlushSaver Smart Toilet Systems” are available from Water Conservation Services 02 9971 1014

The FlushSaver infrared sensor Tap & Shower units are a wall mounted Glass finished unit. Swipe for water activation (water) pulse free operation, adjustable IR beam, quiet water hammer free operation. 10 second operation with externally adjustable timers (within 10% pre-set max and mins) and can be factory customised to suit customer requirements. “FlushSaver Smart Toilet Systems” are available from Water Conservation Services 02 9971 1014